---
title: A Case Study on Root Port Selection
description: CCIE and Boson Training Instructor Bryan Baize shares a study on root port selection.
---

[Network Simulation & IT Training | Boson Blog ](https://blog.boson.com)

# [A Case Study on Root Port Selection](https://blog.boson.com/bid/53329/a-case-study-on-root-port-selection)

 Written by [Kelson Lawrence](https://blog.boson.com/author/kelson-lawrence) | Feb 8, 2011 4:20:00 PM

By [Bryan Baize](http://www.boson.com/Bryan%20Baize), CCIE #16139

ASW1 is connected to DSW1 on F0/1 and F0/2, F0/1 connects to F0/11 on DSW1, F0/2 connects to F0/12 on DSW1. With default configuration on both switches. Initial **show spanning-tree** has DSW1 as Root, ASW1 is using F0/1 as the root port.

**ASW1#show spanning-tree**

**VLAN0001  
Spanning tree enabled protocol ieee  
Root ID Priority 32769  
Address 0009.e81a.6f00  
Cost 19  
Port 1 (FastEthernet0/1)  
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec**

**Bridge ID Priority 32769 (priority 32768 sys-id-ext 1)  
Address 000d.2989.edc0  
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec  
Aging Time 300**

**Interface Role Sts Cost Prio.Nbr Type  
---------------- ---- --- --------- -------- --------------------------------  
Fa0/1 Root FWD 19 128.1 P2p  
Fa0/2 Altn BLK 19 128.2 P2p  
**

**DSW1#show spanning-tree**

**VLAN0001  
Spanning tree enabled protocol ieee  
Root ID Priority 32769  
Address 0009.e81a.6f00  
This bridge is the root  
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec**

**Bridge ID Priority 32769 (priority 32768 sys-id-ext 1)  
Address 0009.e81a.6f00  
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec  
Aging Time 300**

**Interface Role Sts Cost Prio.Nbr Type  
---------------- ---- --- --------- -------- --------------------------------  
Fa0/11 Desg FWD 19 128.11 P2p  
Fa0/12 Desg FWD 19 128.12 P2p **

Test #1 Should port priority be set locally or upstream? Conclusion Upstream.

The following demonstrates that changing port priority on ASW1 F0/1 or F0/2 has no effect on root port selection.

**ASW1#configure terminal  
Enter configuration commands, one per line. End with CNTL/Z.  
ASW1(config-if)#spanning-tree port-priority 10  
% Port Priority in increments of 16 is required**

**ASW1(config-if)#spanning-tree port-priority 16  
ASW1(config-if)#end  
ASW1#show spanning-tree**

**VLAN0001  
Spanning tree enabled protocol ieee  
Root ID Priority 32769  
Address 0009.e81a.6f00  
Cost 19  
Port 1 (FastEthernet0/1)  
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec**

**Bridge ID Priority 32769 (priority 32768 sys-id-ext 1)  
Address 000d.2989.edc0  
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec  
Aging Time 300**

**Interface Role Sts Cost Prio.Nbr Type  
---------------- ---- --- --------- -------- --------------------------------  
Fa0/1 Root FWD 19 16.1 P2p  
Fa0/2 Altn BLK 19 128.2 P2p  
Fa0/5 Desg FWD 100 128.5 Shr**

**ASW1#configure terminal  
Enter configuration commands, one per line. End with CNTL/Z.  
ASW1(config)#int f0/2  
ASW1(config-if)#spanning-tree port-priority 16  
ASW1(config-if)#end  
ASW1#show spanning-tree**

**VLAN0001  
Spanning tree enabled protocol ieee  
Root ID Priority 32769  
Address 0009.e81a.6f00  
Cost 19  
Port 1 (FastEthernet0/1)  
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec**

**Bridge ID Priority 32769 (priority 32768 sys-id-ext 1)  
Address 000d.2989.edc0  
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec  
Aging Time 300**

**Interface Role Sts Cost Prio.Nbr Type  
---------------- ---- --- --------- -------- --------------------------------  
Fa0/1 Root FWD 19 128.1 P2p  
Fa0/2 Altn BLK 19 16.2 P2p  
Fa0/5 Desg FWD 100 128.5 Shr **

Changing the port cost on DSW1 port F0/12 causes ASW1 to change it's root port to F0/2

**DSW1#configure terminal  
Enter configuration commands, one per line. End with CNTL/Z.  
DSW1(config)#int f0/12  
DSW1(config-if)#spanning-tree port-priority 16  
DSW1(config-if)#do show spanning-tree**

**VLAN0001  
Spanning tree enabled protocol ieee  
Root ID Priority 32769  
Address 0009.e81a.6f00  
This bridge is the root  
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec**

**Bridge ID Priority 32769 (priority 32768 sys-id-ext 1)  
Address 0009.e81a.6f00  
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec  
Aging Time 15**

**Interface Role Sts Cost Prio.Nbr Type  
---------------- ---- --- --------- -------- --------------------------------  
Fa0/11 Desg FWD 19 128.11 P2p  
Fa0/12 Desg FWD 19 16.12 P2p**

**ASW1(config-if)#do show spanning-tree**

**VLAN0001  
Spanning tree enabled protocol ieee  
Root ID Priority 32769  
Address 0009.e81a.6f00  
Cost 19  
Port 2 (FastEthernet0/2)  
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec**

**Bridge ID Priority 32769 (priority 32768 sys-id-ext 1)  
Address 000d.2989.edc0  
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec  
Aging Time 15**

**Interface Role Sts Cost Prio.Nbr Type  
---------------- ---- --- --------- -------- --------------------------------  
Fa0/1 Altn BLK 19 128.1 P2p  
Fa0/2 Root LIS 19 128.2 P2p  
Fa0/5 Desg FWD 100 128.5 Shr  
**

Test #2 Should port cost be changed locally or upstream? Conclusion: locally

ASW1 is connected to DSW1 on F0/1 and F0/2, F0/1 connects to F0/11 on DSW1, F0/2 connects to F0/12 on DSW1. With default configuration on both switches. Initial **show spanning-tree** has DSW1 as Root, ASW1 is using F0/1 as root port.

**ASW1#show spanning-tree**

**VLAN0001  
Spanning tree enabled protocol ieee  
Root ID Priority 32769  
Address 0009.e81a.6f00  
Cost 19  
Port 1 (FastEthernet0/1)  
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec**

**Bridge ID Priority 32769 (priority 32768 sys-id-ext 1)  
Address 000d.2989.edc0  
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec  
Aging Time 300**

**Interface Role Sts Cost Prio.Nbr Type  
---------------- ---- --- --------- -------- --------------------------------  
Fa0/1 Root FWD 19 128.1 P2p  
Fa0/2 Altn BLK 19 128.2 P2p**

**  
DSW1#show spanning-tree**

**VLAN0001  
Spanning tree enabled protocol ieee  
Root ID Priority 32769  
Address 0009.e81a.6f00  
This bridge is the root  
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec**

**Bridge ID Priority 32769 (priority 32768 sys-id-ext 1)  
Address 0009.e81a.6f00  
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec  
Aging Time 300**

**Interface Role Sts Cost Prio.Nbr Type  
---------------- ---- --- --------- -------- --------------------------------  
Fa0/11 Desg FWD 19 128.11 P2p  
Fa0/12 Desg FWD 19 128.12 P2p**

**Changing the port cost on ASW1 F0/2 causes the root port to change.**

**ASW1#configure terminal  
Enter configuration commands, one per line. End with CNTL/Z.  
ASW1(config)#int f0/2  
ASW1(config-if)#spanning-tree cost 10  
ASW1(config-if)#do show spanning-tree**

**VLAN0001  
Spanning tree enabled protocol ieee  
Root ID Priority 32769  
Address 0009.e81a.6f00  
Cost 10  
Port 2 (FastEthernet0/2)  
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec**

**Bridge ID Priority 32769 (priority 32768 sys-id-ext 1)  
Address 000d.2989.edc0  
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec  
Aging Time 15**

**Interface Role Sts Cost Prio.Nbr Type  
---------------- ---- --- --------- -------- --------------------------------  
Fa0/1 Altn BLK 19 128.1 P2p  
Fa0/2 Root LIS 10 128.2 P2p  
Fa0/5 Desg FWD 100 128.5 Shr **

Changing the port cost of DSW F0/11 does not cause ASW1 to change it's root port.

**DSW1#configure terminal  
Enter configuration commands, one per line. End with CNTL/Z.  
DSW1(config)#int f0/11  
DSW1(config-if)#spanning-tree cost 1  
DSW1#show spanning-tree**

**VLAN0001  
Spanning tree enabled protocol ieee  
Root ID Priority 32769  
Address 0009.e81a.6f00  
This bridge is the root  
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec**

**Bridge ID Priority 32769 (priority 32768 sys-id-ext 1)  
Address 0009.e81a.6f00  
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec  
Aging Time 300**

**Interface Role Sts Cost Prio.Nbr Type  
---------------- ---- --- --------- -------- --------------------------------  
Fa0/11 Desg FWD 1 128.11 P2p  
Fa0/12 Desg FWD 19 128.12 P2p**

**ASW1#show spanning-tree**

**VLAN0001  
Spanning tree enabled protocol ieee  
Root ID Priority 32769  
Address 0009.e81a.6f00  
Cost 10  
Port 2 (FastEthernet0/2)  
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec**

**Bridge ID Priority 32769 (priority 32768 sys-id-ext 1)  
Address 000d.2989.edc0  
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec  
Aging Time 300**

**Interface Role Sts Cost Prio.Nbr Type  
---------------- ---- --- --------- -------- --------------------------------  
Fa0/1 Altn BLK 19 128.1 P2p  
Fa0/2 Root FWD 10 128.2 P2p  
Fa0/5 Desg FWD 100 128.5 Shr ****  
**

 

 

 

 

Root credit: [http://www.flickr.com/photos/sis/](http://www.flickr.com/photos/sis/) / [CC BY 2.0](http://creativecommons.org/licenses/by/2.0/)

[View full post](https://blog.boson.com/bid/53329/a-case-study-on-root-port-selection)

```json
{
  "@context" : "http://schema.org",
  "@type" : "BlogPosting",
  "author" : {
    "@type" : "Person",
    "name" : "Kelson Lawrence"
  },
  "dateModified" : "2019-08-15T20:19:15.408Z",
  "datePublished" : "2011-02-08T16:20:00Z",
  "headline" : "A Case Study on Root Port Selection",
  "image" : {
    "@type" : "ImageObject",
    "height" : 169,
    "url" : "//cdn2.hubspot.net/hub/70217/file-15267651-jpg/images/root-port-blog.jpg",
    "width" : 450
  },
  "mainEntityOfPage" : "https://blog.boson.com/bid/53329/a-case-study-on-root-port-selection",
  "publisher" : {
    "@type" : "Organization",
    "logo" : {
      "@type" : "ImageObject",
      "height" : 60,
      "url" : "/hs/hsstatic/content_shared_assets/static-1.4092/img/default-amp-logo.png",
      "width" : 60
    },
    "name" : "IT Certification and Training Blog"
  }
}
```